Search:

Type: Posts; User: Vladyman

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    854

    Valves and fittings

    How to simulate valves and fittings?

    I was planning to use a coefficient. Is there a guide for coefficients for different fittings (valves, elbows, tees)?
    I was also planning to use equivalent...
  2. Replies
    1
    Views
    1,298

    pump shutoff head

    I have a pump with a shutoff head 76 m
    However, when I run the simulation I get a head gain of 96 m
    The pump is pumping from reservoir with 5 m head.

    Why do I get a head gain of 96m (shutoff...
  3. Replies
    3
    Views
    1,850

    Thank you very much I got the doubt because I...

    Thank you very much
    I got the doubt because I got good results in the calibration; about 2 psi difference and identifying critical bad condition pipes with very low C (some already verified a leak...
  4. Replies
    3
    Views
    1,850

    Fire Hydrant head losses

    I am performing some hydrant curve simulations. However, I got a doubt.
    Fire hydrants also experience a local head loss.
    Is there an option to include a local head loss in a fire hydrant node? Is...
  5. Replies
    3
    Views
    1,633

    Thank you. One question. How do I apply a...

    Thank you.

    One question. How do I apply a constant initial temperature?
    The first time step I get one temperature (about 27 C), but from the second time step and the other it goes to 0. How can I...
  6. Replies
    1
    Views
    1,144

    Water quality chlorine set up

    I ahve some doubts when simulating water quality

    *How do I define if I want to use first order decay or second order decay?

    *When simulating water quality chlorine, how do I enter the...
  7. Replies
    3
    Views
    1,633

    Water temperature

    InfoWater has the option to simulate water temperature (in water quality). However, it provide no information about the algorithm of data input.
    What are the physical principles used to simulate...
  8. Thank you. I attach a video showing the bug...

    Thank you.

    I attach a video showing the bug (water age only shows 2 breaks). I attach a link because the video is quite big (90MB)...
  9. Map Display Questions (Potential InfoWater 12.4 issues?)

    I got some bugs using InfoWater v12.4

    When I want to plot water age, the palette only has 2 colors (1 break). When I try to get additional breaks it always goes back to the default 1 break
    I...
  10. Replies
    3
    Views
    1,906

    Thank you very much. Sorry, one more question. I...

    Thank you very much. Sorry, one more question.
    I added the dummy loop with booster and pump. Results show 2 phases (attached image). A first phase in which chlorine tends to decrease. Then, it...
  11. Replies
    3
    Views
    1,761

    Thank you very much One more question. Are...

    Thank you very much
    One more question.
    Are there any guidances for the float valve flow vs headloss curve? or each brand provides its own curves?
  12. Replies
    3
    Views
    1,761

    floating valve

    I have a tank and I want to include a floating valve

    Without any valve the connecting pipe has a flow about 1000 cmd and a headloss about 2 m

    The minimum tank level is 1m, and the maximum tank...
  13. Replies
    3
    Views
    1,906

    input chlorine at given times

    I would like to simulate one case where the chlorine in one strage tank is regulated every day. Every day at a given time, chlorine is regulated at given concentration (e.g. 1 mg/l).

    I specify the...
  14. Replies
    1
    Views
    1,828

    unbalancing due to 1 pipe

    I am preparing a mode
    The model run ok, balances after 32 iteartions.
    When I add 1 pipe connected to one node with demand zero, then the model does not balance. I increase to 200 iteration but...
  15. Replies
    3
    Views
    2,450

    Thank you Bob, I sent you an e-mail ...

    Thank you Bob,

    I sent you an e-mail

    vladimir.gomez@kankyoscience.com
  16. Replies
    3
    Views
    2,450

    sewer or SWMM animation

    I am preparing a presentation. I want to present some capabilities of InfoSewer and SWMM (try to make a project).
    I would like to add an animation showing results of simulation (2D overland flow and...
  17. Replies
    3
    Views
    2,731

    Thank, I am using 12.4 Update 1 Other bug,...

    Thank,
    I am using 12.4 Update 1

    Other bug, is that sometimes I cannot visualize the water age. I can visualize flow, headloss, diameter and everything. But when I go to water age, it does not...
  18. Replies
    3
    Views
    2,731

    problem running InfoWater v12

    I updated InfoWater to v12.
    However, I have a problem.
    I successfully run a simulation. However, when I perform and try to run a simulation, it only refreshes the screen, but it does not show the...
  19. Replies
    1
    Views
    1,641

    visualization error

    I run a simulation, but when I go to the Map Display I get the error:

    Read Data:System.NullReferenceException: Object reference not set to an instance of an object....
  20. Replies
    1
    Views
    1,629

    Copy model to another PC

    I have some water distribution models in InfoWater
    I want to copy them to another computer. I copied the whole:
    xxx.out folder
    xxx.IWDB folder
    xxx.mxd map

    When I try to open them in the new...
  21. Replies
    1
    Views
    2,172

    Question operating tanks

    I have a pipe that connects a city pipe connection with a tank (attached figure). The city connection is represented by a reservoir with a PRV.
    Total head PRV = 118 m
    Total head tank = 91 m
    Pipe...
  22. Replies
    1
    Views
    2,722

    GIS Gateway update GIS

    I want to use GIS Gateway to update original GIS data that was used to create a model.
    In InfoWater I added new pipes and changed diameters. I would like to update the original GIS to reflect such...
  23. Replies
    1
    Views
    1,602

    modelling contaminant decay

    InfoWater can be used to simulate the decay of contaminants such as chlorine. There are several reference guides about reasonable decay constant k for chlorine.
    I would like to analyze the decay of...
  24. Replies
    1
    Views
    3,371

    Pump curve NPSH

    I have a pump curve (attachment). The curve that is supposed to show the NPSH shows Flow vs Horsepower.
    How can I input this curve? Do I use the curve type 4 (NPSH vs Flow)?
    416
  25. Message: unable to locate geometry data for pipe

    I get the following warning message:
    WARNING unable to locate geometry data for pipe '460'
    WARNING unable to locate information data for Junction 'J1502'

    I get those same messages for other...
Results 1 to 25 of 57
Page 1 of 3 1 2 3